Cut Wood Wallcovering

$ 96.00$ 144.00

Please note:  this product is temporarily out of stock.

  • Dimensions:  24 inches (width); available lengths: 8 feet; 10 feet; or 12 feet.
  • Self-adhesive matte vinyl with semi-permanent adhesive backing & siliconized kraft liner to prevent image from chipping or cracking.
  • Nonsolvent based inks (solvent-based ink-jet ink has many health and safety considerations including: respiratory, skin and eye irritants, and in some cases, central nervous system depressants).
  • Positional or removable applications for up to three (3) months.
  • Lead times range from two (2) to four (4) weeks. Please [iphorm_popup id=”1″ name=”Contact Us”]contact Abode New York [/iphorm_popup]for assistance.
  • Made in Brooklyn, New York.

NYC small




Free Shipping on Order over $150


Cut Wood Wall Panel – modern cabin style

Cut Wood

Cut Wood detail

The mountain air was colder than the lowlands. Alberto pitched our tent while I began looking for wood. We had a fire going in no time, and we fed it all night. After dinner, we hiked down to the lake where we watched the ripples and fireflies move above them. When we got back to camp, I stripped down and crawled into my sleeping bag. Alberto joined me for extra warmth, the fire outside had died down, but we still had plenty of wood.

Although launched in 2011, Filthy Home designs have been budding for decades. Inspired by raw, simple perspectives, Filthy Home resonates with vintage flare and modern sensuality. Capturing basic moments in life, both contemporary and historic, the company values the unusual and sometimes unspoken familiarities that we all share in the overall experience of being human. Often fueled by those random explosions of creativity, embracing rather than avoiding traditional taboos, Filthy Home will rouse your senses. Go ahead…savor our specialties.

Instruction for installation of Boarding School Wall Panel:

Cut Wood

Two panels of Cut Wood

Step 1: Patch any large holes using joint compound and a putty knife. Allow the patches to dry completely, then sand smooth with a fine grit sandpaper.
Step 2: Apply a coat of fresh satin or gloss paint using a paint roller (the wall HAS TO BE CLEAN), using a paint brush to cut in with primer around the edges (this product sticks very well to all clean surfaces).
Step 3: Use a level and pencil to draw vertical guidelines on the wall. You should space these lines so you can perfectly align the rows of vinyl wallpaper.
Step 4: Cut a your wallpaper panel so there is an extra 6 to 8 inches longer than actually needed . Peal back the backing to exposes the adhesive wallpaper (just like a huge sticker).
Step 5: Place the wallpaper on the wall, aligning it with a set of vertical pencil guidelines.  Allow a small amount of overlap on the top and bottom of the wall.  Trim the wallpaper after it has been installed.
Step 6: Smooth the vinyl wallpaper using a rubber roller (use a clean printmaking ink roller and work from the PERFECTLY alined starting point to the panel edge). A regular wallpaper smoothing brush doesn’t really work to remove bubbles. For any bubbles you can’t remove, use a needle to pierce the bubble. Then press the bubble to release any air and smooth the wallpaper.
Step 7: Apply the next piece of wallpaper, using the same method you used to apply the first piece. Make sure that the edges of any pattern matches. There is some give to the vinyl. If you get a bit off your alignment pull back the adhesive panel a few inches and reposition moving down the wall.
Step 8: After you have applied all of the wallpaper on a wall, trim the top and bottom using a metal straightedge and utility blade. (Be careful not to scratch the paper. (Patience is a virtue here!)
Step 9: Install the vinyl onto the next wall, using the same techniques you used to install the wallpaper on the first wall. Continue until all of the walls are covered.

Additional information

Weight 4 lbs
Dimensions 28 x 6 x 6 in

8 feet, 10 feet, 12 feet